The default for the Connect command is to simply enter the 4- 5-, or 6-digit node number to which you wish to connect. Restores normal transmission from RF to the Internet. Inhibits transmission from RF to the Internet. Switches to a different stored set of configuration settings (0 through 9). Looks up a station by its node number, and reads back its callsign and status. Looks up a station by its callsign, and reads back its node number and status. Re-connects to the station that most recently disconnected.Īnnounces the callsign of each station currently connected.ĭisables EchoLink (no connections can be established). If more than one station is connected, disconnects only the most-recently-connected station. Selects a conference server at random from the Favorites List, and tries to connect to it.ĭisconnects the station that is currently connected. Selects an available link or repeater (-L or -R) at random from the Favorites List, and tries to connect to it. Selects an available node (of any type) at random from the Favorites List, and tries to connect to it. Selects an available single-user station at random, and tries to connect to it. Selects a conference server at random, and tries to connect to it. Selects an available link or repeater (-L or -R) at random, and tries to connect to it.
Selects an available node (of any type) at random, and tries to connect to it. Note:// If you have upgraded from an earlier version of EchoLink, you may need to choose “Reset to Defaults” to make all of the following commands available.Ĭonnects to a station on the Internet, based on its node number.Ĭonnects to a station on the Internet, based on its callsign. The table below lists each of the DTMF commands. Although a set of default sequences is assigned to each function, any sequence can be customized using the DTMF tab of the Sysop Settings page. These commands are used to enable or disable the link, or to connect or disconnect a station on the Internet.Įach command consists of a sequence of digits (or the special keys *, #, and A through D). This will disconnect the nodes.ĮchoLink can be configured to accept commands through the local radio receiver using DTMF tones (TouchTones). When you have finished talking, use the DTMF buttons and dial in 73.The best protocol is to wait a couple of seconds between hearing the other person and starting to talk yourself. There will be a delay between sending and receiving when using Echolink or IRLP.A message will tell you if you either are successful or unsuccessful. Use a DTMF microphone and dial in the node number that you wish to contact.Repeater listings such as this one for Australia, will provide useful information in your search. Locate a node close to you and one that you would like to contact.If you use Google Earth, this kmz file will show you the connections between Echolink nodes. This list is updated regularly, and gives information about which nodes are connected to each other. Look here to find out which nodes are available and where they are located.The user selects a contact from the list and communication is carried out using the computer microphone. The Echolink application presents a window such as the one below to the user. Some ISP’s may allow multiple unique external IP addresses, in which case Echolink can be used on multiple computers.
HOW TO ADD ECHOLINK APP TO ZELLO PC
Using Echolink on a computerĪs Echolink is using internet protocols for transmission of voice, various ports must be open in your firewall for it to operate properly, the Echolink website summarising the requirements thus: A minimum connection speed of 256KBs is usually recommended for effective, clear VOIP applications. VOIP connections of any sort – including Echolink – require a DSL connection to the internet.
HOW TO ADD ECHOLINK APP TO ZELLO MAC
Application versions are available for PC and Mac computers.Įcholink is not usually described as a digital mode – although VOIP is the digital transmission of voice – as most operators will use an FM radio to connect to the Echolink network. It is similar to IRLP but allows users to connect via either radio or computer. Echolink is a VOIP (Voice Over IP) application that allows amateurs to connect to one another using the internet.
0 kommentar(er)
